Home

Licensing

NSW Plumbing Contractor Licence: RPL Towards CPC40920

In NSW, a plumbing contractor licence or qualified supervisor certificate needs CPC40920 Certificate IV in Plumbing and Services (or later) and at least two years of paid industry experience. Any plumbing, draining or gasfitting work needs a licence or certificate, whatever it costs. RPL can recognise your skills towards CPC40920. The experience is assessed separately.

Start my Free Skills Review

Free · Confidential · No obligation

Plumbing is licensed differently in NSW.

Most NSW trade licences start at jobs worth more than $5,000. Plumbing doesn't. You need a licence or certificate for any plumbing, draining or gasfitting work, including LP gasfitting, whatever the cost and whether it's residential, commercial or industrial. You also need to be licensed in every category you work in.

The rules below come from the NSW Government's plumbing, draining and gasfitting page, which is managed by Building Commission NSW.

Licence types.

There are four types: an individual contractor licence, a company or partnership contractor licence, a qualified supervisor certificate, and a tradesperson certificate (or provisional tradesperson certificate). Someone with a tradesperson certificate works under the general supervision of a contractor licence or qualified supervisor certificate holder. Anyone without a licence, including apprentices, must be under immediate supervision.

Licence or certificateQualification NSW listsExperience
Contractor licence or qualified supervisor certificate (plumbing, draining, gasfitting)Certificate IV in Plumbing and Services (Operations), CPC40920 or laterA completed apprenticeship or traineeship plus at least two years' combined industry experience (during or after it), or at least two years after your Certificate III in Plumbing
Tradesperson certificate (plumbing, draining and gasfitting)Certificate III in Plumbing, CPC32420 or laterNot listed for this certificate

Licences and certificates are issued for 1, 3 or 5 years, except provisional tradesperson certificates, which run for 3 years and can't be renewed. Individual applicants need a National Police Check no older than four months. Some categories, including draining, gasfitting and specialist water plumbing such as fire protection or irrigation, can also be licensed with a Certificate III in Plumbing plus listed units instead. The official page lists the units for each.

If you hold a tradesperson certificate, you work under the general supervision of a licence holder. Moving to a contractor licence or qualified supervisor certificate is what lets you contract for work in your own right, or supervise others, once you meet the qualification and experience rules.

The experience rules.

  • Experience means work as an employee, paid in line with an award or enterprise agreement.
  • It can be gained during or after an apprenticeship or traineeship.
  • If you haven't completed an apprenticeship or traineeship, experience only counts from the date your Certificate III in Plumbing was issued. Anything before that isn't accepted.
  • Referees confirm your experience on the plumbing referee statement form.

What CPC40920 covers.

CPC40920 has 15 units: 10 core units and 5 electives, with different elective rules depending on the pathway. NSW lists the Operations award, so for a licence your electives need to make up the Operations award, not hydraulic services design. These are the core units:

CPC40920 Certificate IV in Plumbing and Services core units (release 4). Source: training.gov.au, checked 2026-11-16.
CodeUnit
BSBESB402Establish legal and risk management requirements of new business ventures
CPCCBC4012Read and interpret plans and specifications
CPCPCM4011Carry out work-based risk control processes
CPCPCM4012Estimate and cost work
CPCPCM4015Access and interpret regulatory requirements for the plumbing and services industry
CPCPDR4011Design and size sanitary drainage systems
CPCPDR4012Design and size stormwater drainage systems
CPCPGS4011Design and size consumer gas installations
CPCPSN4011Design and size sanitary plumbing systems
CPCPWT4011Design and size heated and cold-water services and systems

Where RPL fits.

If you're a licensed tradesperson who has been running jobs, supervising apprentices, quoting and dealing with clients, RPL can recognise those skills towards CPC40920. A partner RTO assesses your evidence against each unit, and gap training may be needed for anything your work hasn't covered.

Evidence that usually helps: quotes and invoices you've prepared, job plans and hydraulic drawings you've worked from, compliance paperwork, and references from the licence holders you've worked under.

How to apply.

  1. Hold CPC40920 (or later) and at least two years of eligible, paid experience.
  2. Get referee statements from the licence holders you've worked under.
  3. Get a National Police Check no older than four months.
  4. Apply in every category you work in, through Building Commission NSW or Service NSW.

If you hold a licence from another state or New Zealand, NSW has a separate mutual recognition process, and plumbing is included in the NSW Automatic Mutual Recognition scheme.

Read more about the CPC40920 Certificate IV in Plumbing and Services via RPL, or see the Certificate IV RPL cost guide.

Qualifications gained through RPL are nationally recognised under the Australian Qualifications Framework (AQF). They are assessed and issued by partner Registered Training Organisations (RTOs). If your evidence doesn't cover every unit of competency, gap training may be needed.

Common questions.

Do I need a licence for small plumbing jobs in NSW?

Yes. NSW requires a licence or certificate for any plumbing, draining or gasfitting work, whatever it costs and whether it's residential, commercial or industrial.

What's the difference between a tradesperson certificate and a contractor licence?

A tradesperson certificate holder works under the general supervision of a contractor licence or qualified supervisor certificate holder. The contractor licence and supervisor certificate need the Certificate IV and experience.

Does experience before my Certificate III count?

If you haven't completed an apprenticeship or traineeship, NSW only counts experience from the date your Certificate III in Plumbing was issued.

Can RPL get me CPC40920?

RPL can recognise skills you already have towards CPC40920. A partner RTO assesses your evidence, and gap training may be needed. The outcome is not guaranteed, and the licence still needs the experience.

Sources.

Start my Free Skills Review